Search Results

The introduction of real driving emissions cycles and increasingly restrictive emissions regulations force the automotive industry to develop new and more efficient solutions for emission reductions. In particular, the cold start and catalyst heating conditions are crucial for modern cars because is when most of the emissions are produced. One interesting strategy to reduce the time required for catalyst heating is post-oxidation. It consists in operating the engine with a rich in-cylinder mixture and completing the oxidation of fuel inside the exhaust manifold. The result is an increase in temperature and enthalpy of the gases in the exhaust, therefore heating the three-way-catalyst. The following investigation focuses on the implementation of post-oxidation by means of scavenging in a four-cylinder, turbocharged, direct injection spark ignition engine. The investigation is based on detailed measurements that are carried out at the test-bench.

The present article is concerned with the investigation of the engine noise induced by the piston slap of an actual passenger car Diesel engine. The focus is put on the coherence of piston secondary movement, impact of the piston on the cylinder liner, generated structure-borne noise excitation of the engine structure and the occurring acceleration on the engine surface. Additionally, the influence of a varying piston-pin offset and piston clearance is evaluated. The analyses are conducted using an elastohydrodynamic multi-body simulation model, taking into account geometry, stiffness and mass information of the single components as well as considering elastic and hydrodynamic behavior of the piston-liner contact. A detailed description of the simulation model will be introduced in the article. The obtained results illustrate the piston secondary motion and the related structure-borne noise on the engine surface for several piston-pin offsets and piston clearances.

The performance of three way and NOx catalysts was evaluated on vehicles utilizing non-feedback fuel control and electronic feedback fuel control. The vehicles accumulated 80,450 km (50,000 miles) using fuels representing the extremes in hydrogen-carbon ratio available for commercial use. Feedback carburetion compared to non-feedback carburetion improved highway fuel economy by about 0.4 km/l (1 mpg) and reduced deterioration of NOx with mileage accumulation. NOx emissions were higher with the low H/C fuel in the three way catalyst system; feedback reduced the fuel effect on NOx in these cars by improving conversion efficiency with the low H/C fuel. Feedback had no measureable effect on HC and CO catalyst efficiency. Hydrocarbon emissions were lower with the low H/C fuel in all cars. Unleaded gasoline octane improver, MMT, at 0.015g Mn/l (0.06 g/gal) increased tailpipe hydrocarbon emissions by 0.05 g/km (0.08 g/mile).

4 different engine concepts with Catalyst have been developed in regard to pollutant emission, fuel efficiency and performance. Despite the wide power range from 1,2 HP to 12 HP and the different applications of these engines to Mopeds, Chainsaws and Motorcycles, the problems to solve have been similar. Internal measures such as optimized carburetion, cooling, piston shape and clearance, scavenging and tuning of the exhaust must enable the engine to run on the lean side. This is imperative to supply sufficient oxygen for the exothermal reaction and to keep the energy to be converted in the Oxidation Catalyst at a minimum. Secondary measures have been taken to shorten the Catalyst's light-off and to keep the temperature range in limits.

In Sports Motorcycles category, fuel injection systems have been employed more popularly in recent years, and we have been also developing motorcycles introducing fuel injection systems in the category of 600cc - 1400cc displacement. Sports Motorcycles need to be controlled in a wide range from idling to over 10000rpm. Better throttle response, high power and low fuel consumption are also required. Therefore, adding to optimizations of inlet system layout, fuel injection amount, injection timing and ignition timing, the authors have applied to some models electric control devices such as SDTV (Dual Throttle Valve System) that controls intake air amount with secondary throttle valve located upstream of primary throttle valve and SET (Exhaust Tuning System) that controls exhaust pressure by opening angle of an exhaust valve installed in an exhaust pipe to improve the torque characteristics.

Four new 2-cylinder 4-stroke concepts are displayed as design and fitted in vehicles. These four different concepts comprise a Modular Concept V2- and W3-cylinder a MotoGP / Superbike concept with 2 and 3 cylinders, a narrow angle V-engine and a Building Block System Commuter CVT engine. Each engine concept is designed to meet the different requirements of the four segments. Specific analysis and simulation concerning 1D thermodynamics, vehicle simulation and delivered performance and tractive force was done for each concept. The concepts are compared in the aspects of uniform rotation, inertia forces and moments, and the effect on performance by the pulse effects of the manifolded intake and exhaust systems. The Modular Concept contains an OHC engine with a wide range of displacements and commonality of many parts. Good versatility is obtained as the concepts can be applied for sport- or custom bikes.

The Rotating Cylinder Valve (RCV) Engine is a novel 4 cycle engine that is a practical alternative to conventional 2 and 4 stroke designs, in particular for small capacity single cylinder applications. It is primarily intended to address applications where emissions legislation is forcing manufacturers to abandon the traditional carburetted 2 stroke. It has particular benefits for the moped/light motorcycle market. The engine operates on a simple principle. The cylinder liner is rotated around the piston at half engine speed via a pair of bevel gears. A port in the side of this cylinder indexes with inlet and exhaust ports in the surrounding casing. This rotary valve serves the cylinder as the engine cycles through the conventional 4 stroke cycle. The main technical issue that has been addressed is the design of a practical rotary valve seal.

TCT - Total Combustion Technology is technology designed to enable small SI four-stroke and two-stroke engines to meet current and proposed emission standards that pertain to small engines. This paper outlines the technology, the testing equipment, and the results from tests comparing TCT to original carburetors on two different engines. The comparison shows clearly that emissions can be reduced substantially by TCT. The MLC (Mechanical Lambda Control) feature of TCT allows the emission profile of the engine to be matched to the application in each case.

A sequentially stratified scavenged engine is characterised by the principle that the cylinder is first scavenged by pure air, followed by the air/fuel mixture. The air is introduced into the upper part of the scavenging ducts through a piston port or a reed valve. To take full advantage of the stratified scavenged principle, the scavenging ducts have to be designed in a way, so that they can accommodate all the air that is delivered into the scavenging ducts. When converting a conventional two-stroke engine into a stratified scavenging engine, it is also important that the tuning and basic scavenging characteristics of the standard engine are not deteriorated. In this paper it is shown how these two aspects can be combined. Together with a theoretical approach for dimensioning the volume and length of the scavenging ducts, it gives a guideline on how to design the basic engine layout, for a stratified scavenged two-stroke engine.

In order to meet the new stringent emission limits for small handheld power tools technologies like methods to improve the scavenging process and after treatment devices are deployed. Additionally, professional machines such as chain saws add particular requirements to avoid mechanical failures. By precise control of the carburetion it is possible to yield the necessary reduction of the emission level yet to maintain the performance of the engine. Thus, the development of an Electronically Controlled Carburetion System to reduce the exhaust emissions of small IC engines for handheld power tools was initiated at the WHZ, Germany. Key requirements of such a system are: low cost, high reliability, low electrical power consumption, high accuracy in metering the fuel demand of the engine. First results are promising. A correlation between exhaust gas temperature and the fuel demand of the engine was confirmed for both, wide open throttle and part load operation.

In this study, the heated fuels were provided to the diesel engine in order to activate the fuel before the injection. Two test fuels: the normal diesel fuel and cetane, which have different boiling points were used. For both normal diesel fuel and cetane, crank angles at ignition and maximum pressure are delayed and the maximum combustion pressure is decreased as the fuel temperature rises. In cases of large and middle mass flow rate of fuel injection, the brake thermal efficiency and brake mean effective pressure are decreased when the fuel temperature is higher than 570 [K]. However, in the case of small mass flow rate of fuel injection, the brake thermal efficiency is almost independent of fuel temperature. HC and CO concentrations in the exhaust gas emission show constant values regardless of fuel temperature. However, NOx concentration is gradually decreased as the fuel temperature rises.

The 912 engine is a well known 4-cylinder horizontally opposed 4-stroke liquid-/air-cooled aircraft engine. The 912 family has a strong track record: 40 000 engines sold / 25 000 still in operation / 5 million flight hours annually. 88% of all light aircraft OEMs use Rotax engines. The 912iS is an evolution of the Rotax 912ULS carbureted engine. The “i” stands for electronic fuel injection which has been developed according to flight standards, providing a better fuel efficiency over the current 912ULS of more than 20% and in a range of 38% to 70% compared to other competitive engines in the light sport, ultra-light aircraft and the general aviation industry. BRP engineers have incorporated several technology enhancements. The fully redundant digital Engine Control Unit (ECU) offers a computer based electronic diagnostic system which makes it easier to diagnose and service the engine.

In July 1997, the Pacific Northwest and Alaska Regional Bioenergy Program, in cooperation with several industrial and institutional partners initiated a long-haul 322,000 km (200,000 mile) operational demonstration using a biodiesel and diesel fuel blend in a 324 kW (435 HP), Caterpillar 3406E Engine, and a Kenworth Class 8 heavy duty truck. This project was designed to: develop definitive biodiesel performance information, collect emissions data for both regulated and non-regulated compounds including mutagenic activity, and collect heavy-duty operational engine performance and durability information. To assess long-term engine durability and wear; including injector, valve and port deposit formations; the engine was dismantled for inspection and evaluation at the conclusion of the demonstration. The fuel used was a 50% blend of biodiesel produced from used cooking oil (hydrogenated soy ethyl ester) and 50% 2-D petroleum diesel.

With growing concern about global warming, alternatives to fossil fuels in internal combustion engines are searched. In this context, hydrogen is one of the most interesting fuels as it shows excellent combustion properties such as laminar flame speed and energy density. In this work a CFD methodology for 3D-CFD in-cylinder simulations of engine combustion is proposed and its predictive capabilities are validated against test-bench data from a direct injection spark-ignition (DISI) prototype. The original engine is a naturally aspirated, single cylinder compression ignition (Diesel fueled) unit. It is modified substituting the Diesel injector with a spark plug, adding two direct gas injectors, and lowering the compression ratio to run with hydrogen fuel. A 3D-CFD model is built, embedding in-house developed ignition and heat transfer models besides G-equation one for combustion.

With the increased demand of mobility in the form of two-wheelers and the continued dominant share of Internal Combustion Engines (ICE) in Indian market, there is considerable influence on the deterioration of air quality. The regulators in this region have legislated Bharat Stage 6 (BS6) as a measure to restrict tail pipe emissions, which necessitates the automotive industry to work towards emission optimization measures. Some of the factors influencing this includes, air-fuel mixture formation, spray targeting, fuel properties, flow dynamics, combustion chemical kinetics, exhaust after-treatment etc. The focus area of this paper is to study the influence of air-fuel mixture formation which is highly dependent on fuel droplet atomization, injection timing, fuel injector, injection pressure and mixture preparation techniques to reduce the engine out emissions.

A 3D-CFD model with detailed chemical kinetics was developed to investigate the combustion characteristics of HCCI engines, especially those fueled with hydrogen and n-heptane. The effects of changes in some of the key important variables that included compression ratio and chamber surface temperature on the combustion processes were investigated. Particular attention was given, while using a finer 3-D mesh, to the development of combustion within the chamber crevices between the piston top-land and cylinder wall. It is shown that changes in the combustion chamber wall surface temperature values influence greatly the autoignition timing and location of its first occurrence within the chamber. With high chamber wall temperatures, autoignition takes place first at regions near the cylinder wall while with low surface temperatures; autoignition takes place closer to the central region of the mixture charge.

A 7-cylinder, wobble plate type, infinitely variable displacement, (IVD), compressor has been developed to meet the following requirements as set forth by the world automotive manufacturers: 1 Wide range of capacity control to eliminate clutch cycling which causes temperature and humidity fluctuations of louver outlet air and unexpected engine load variations 2 Near perfect protection of the evaporator against icing 3 Reliability under all field operating conditions 4 Quiet operation in a compact and lightweight package to suit the new trends in automotive design. A simpler mechanism has been applied to the variable angle cam drive and wobble plate rotation prevention method than with the conventional IVD compressor. The 7-cylinder design, with fewer parts for the piston drive mechanism, enables a quiet compressor of 161.3 cc displacement in a 118 mm diameter casing. An internal control valve is integrated in the center of the valve plate assembly.

The production unit number of small diesel engine cars tends to decline except recreational vehicles in Japanese market in recent years, while the production unit number in Europe market keeps on increasing owing to the merits of the durability and the fuel consumption. The small diesel engines will have to be improved in the near future by solving major problems such as noise and vibration pollution, environmental pollution, improvement in performance of diesel engines, in order to expand the production of the engines. This paper refers to a basic study on the experimental and analytical methods for the reduction of resonant vibration in each vibration mode on some cylinder blocks of small high-speed diesel engines in rated engine speed range. Hammering test method, which is easy and useful for measuring frequency response functions, is carried out in the experiments.

Parameters like brake mean effective pressure, mean velocity of the piston, hardness of the wear surface, oil film thickness, and surface areas of critical wear parts are similar for all the diesel engines. The mean piston velocity at the rated speed is nearly the same for all the diesel engines. The mechanical efficiency normalized to an arbitrary brake mean effective pressure (bmep) is dependent on the size of the engine. The engine life seems to be proportional directly to the square of a characteristic dimension namely, cylinder bore of the engine and inversely to speed and load factor for engines varying widely in sizes and ratings.